|
|
|
Sentron Angle Sensor, Linear 2-Axis Hall IC, 2SA-10
 |
| |
 GMW Sin/Cos to Analog Interpolator IC - GMW360A
The GMW360A Interpolator IC is designed to be compatible with the Sentron 2SA-10, 2-Axis angular sensing IC,
however it will work with any SIN and COS signal input with the required input amplitude. The GMW360A is based
on the Cypress PSoCTM, CY8C24123A, Mixed-Signal Array device. The GMW360A converts orthogonal SIN and
COS signals to Analog and PWM output signals proportional to the angle with 9 bit resolution.
GMW360A
Data Sheet - pdf, 1.1MB
|
 360ASM Angle Sensing Module Evaluation Kit - AN_360ASMKIT
Quickly evaluate the Ametes 360ASM-01
Angle Sensor Module for non-contact, 360°, angle sensing applications. The 360ASM-01 combines the Sentron 2SA-10 Two-Axis Linear Hall sensor with the GMW360A Sin/Cos to Analog Interpolator to accurately measure the angle of the magnetic field generated by a small permanent magnet. An analog 2.5V±2.0V signal is available corresponding to 0 ±180° rotation angle. Mechanical adjustment for zero angle is eliminated by having the electrical zero settable to any angle. The Kit includes a small PCB (28x13mm, 1.1x0.5inch) with a connector for the 360ASM-01, 360ASM-01 Module, and a Rotary Holder with Permanent Magnet.
AN_360ASMKIT
Data Sheet - pdf, 221kB
|
 2SA-10
with GMW360A Angle Sensing Evaluation Kit - AN_360KIT
The AN_360KIT enables immediate evaluation of the
Sentron 2SA-10 Two-Axis Hall IC with the GMW360A Interpolator
IC. It generates Analog Linear and PWM signals proportional
to the angle of rotation of a small permanent magnet over
a full 360 degree rotation. Resolution is better than
one degree. Provision is included for setting the electronic
zero at any mechanical angle. (The 2SA-10-SO with GMW360A
is also available packaged as the 360ASM-01
Angle Sensor Module.)
AN_360KIT
Data Sheet - pdf, 1,215kB
|
 2SA-10
Application Engineering Kit - AN_112KIT (Small PCB)
360° Angle Sensing
This kit is useful for evaluating the 2-Axis linear Hall Effect sensor in Angular Position sensing
applications. The kit contains a small 0.5 in sq, assembled printed circuit board with a 2SA-10 soldered
onto the PCB and a flat ribbon cable, a magnet guide, a SmCo magnet that has been magnetized across the
diameter and an extra 2SA-10-SO sample part. The plastic guide fits into four holes on the PCB and
provides a means of centering the magnet over the IC and providing the optimum spacing between the
magnet and IC. As the magnet is manually rotated 360 degrees, the X and Y outputs will provide a sin
and cosine voltage output at the X and Y outputs respectively.
AN_112KIT
Data Sheet - pdf, 83kB
|
 2SA-10
Application Engineering Kit - AN_114KIT (STD. PCB)
360° Angle Sensing
This kit is useful for evaluating the 2-Axis linear Hall Effect sensor in Angular Position sensing
applications. The kit contains an assembled printed 0.5" x 1.0", circuit board with a 2SA-10-SO soldered
onto the PCB, a magnet guide, a SmCo magnet that has been magnetized across the diameter and an extra
2SA-10-SO sample part. The plastic guide fits into four holes on the PCB and provides a means of
centering the magnet over the IC and providing the optimum spacing between the magnet and IC. As
the magnet is manually rotated 360 degrees, the X and Y outputs will provide a sin and cosine voltage
output at the X and Y outputs respectively
AN_114KIT
Data Sheet - pdf, 64kB
|
Permanent Magnet for Angle Sensing - 55B0082
A 6.35mm dia. x 3.81mm SmCo permanent magnet that is polarized
across its' diameter rather than axially. Compatible with
the 2SA-10 and may be mounted into the M250-1.0 Magnet
Holder (shaft).
55B0082 Outline Drawing - pdf, 19kB
|
Permanent Magnet for Angle Sensing - 55C0126
A 6.35mm square x 2.55mm thick SmCo permanent magnet that is polarized
across its' width rather than depth. Compatible with
the 2SA-10.
55C0126 Outline Drawing - pdf, 18kB
|
Magnet Holder and Magnet for Angle Sensing - M250-1.0
The M250-1.0 is an aluminium holder with a 6.35mm diameter
shaft that is 25.4mm long. It comes with a 55B0082 permanent
magnet epoxied into one end of the shaft.
M250-1.0 Outline Drawing with magnet - pdf, 79kB
M250-1.0 Outline Drawing without magnet - pdf, 44kB
|
Magnet Holder and Magnet for Angle Sensing - M250SQ-1.0
The M250SQ-1.0 is an aluminium holder with a 6.35mm diameter
shaft that is 25.4mm long. It comes with a 55C0126 permanent
magnet epoxied into one end of the shaft.
M250SQ-1.0 Outline Drawing with magnet - pdf, 42kB
M250SQ-1.0 Outline Drawing without magnet - pdf, 41kB
Last updated on
9 May, 2007
|
| Back
to Top |
|
|
|
|
|
