Discontinued Products

Description Product Replacement Product

Magnetic Sensors

Sentron 2SA-10G 2-axis Linear Hall Magnetic IC 2SA-10G None
Sentron CSA-1VG-SO Linear Hall Magnetic IC CSA-1VG-SO None
Sentron CSA-1V Hall-Effect High Sensitivity Sensor IC, single-axis, analog, high sensitivity, small size and low power. Replaced by lead free version. CSA-1V-SO 1-axis None
Sentron 2SA-10 Non-Contact, Absolute Angle Sensor IC. Replaced by lead free version. 2SA-10-SO 2-axis None
Senis BBM-01 Bus Bar Module Isolated Current Sensor BBM-01 None
CQ2066 Fully integrated, Hall effect-Based High Accuracy, Fast response linear current sensor. CQ2066 CQ2366
CQ1xx Not recommended for new development. Consider CQ20xx or CX30xx instead. CQ1xx CQ20xx or CQ30xx
Asahi EM-3242 Non-contact Magnetic Angle Sensor EM-3242 None
Asahi AK877x Non-contact Magnetic Angle Sensor AK877x None
Asahi HW-108C InSb Hall Element, High sensitivity, Small, Thin, Motor, SMT HW-108C None
Asahi HW-109A InSb Hall Element, High sensitivity, Motor, SMT HW-109A None
Asahi HW-209A InSb Hall Element, High sensitivity, Motor, SMT HW-209A None
Asahi HW-300A InSb Hall Element, High sensitivity, Motor, DIP HW-300A None
AN_161KIT Universal Hall Elemental Interface Module AN_161KIT None
AN_160KIT Universal Hall Elemental Interface Module AN_160KIT None
Asahi EM-0711 Bipolar Hall Effect Latch, Power down function, SON EM-0711 EM-1711
Asahi EM-0712 Bipolar Hall Effect Latch, Power down function, SON. EM-0712 EM-1712
Asahi EM-0713 Bipolar Hall Effect Latch. Power down function, SON. EM-0713 None
Asahi EM-0771 Unipolar Hall Effect Switch, Pulse excitation, SON EM-0771 EM-1771
Asahi EM-0791 Omnipolar Hall Effect Switch. Pulse excitation, SON. EM-0791 EM-1791
Ametes MFS-3A 3-axis Magnetic Field Sensor MFS-3A MagVector™ MV2
Ametes CM Series 3-channel Current Monitor Ametes CM Series 3 None
Ametes Low Current Sensor Module. Uses CSA-1V. Analog output signal. Three standard ranges Configurable for unipolar or bipolar current. High voltage isolation >4kV. The Ametes CS0.25A-01, CS2.5A-01 & CS10A-01 are no longer in production. CS0.25A-01 CS2.5A-01 CS10A-01 CS0.25A-02 CS2.5A-02 CS10A-02
Ametes 360ASMF Series Angle Sensor, flat profile. Uses 2SA-10 and PSoC. Analog output signal. Four standard angle ranges up to 360°. Encapsulated package only 3.4mm (0.14") thin. 360ASMF EM-3242
2SA-10G
360ASMC-1 Non Contact Absolute Angle Sensor Module 360ASMC-1 None
Ametes 360ASM-01. Angle Sensing Module, 0±180° 360ASM-01 None
Ametes DMFS-3A. Three Axis Magnetic Field Sensor Monitor. DMFS-3A None
Ametes CS-02 Series. High Sensitivity Current Sensor Ametes CS-02 Senis CS-03
Asahi EM-3241 Non-contact, Absolute Angle Sensor IC Integrates a Hall element and processing IC into a single package. EM-3241 is no longer in production. EM-3241 EM-3242
GMW AN_360KIT 2SA-10G with GMW360A Angle Sensing Evaluation Kit AN_360KIT 360ASM-01
GMW360A Interporolator IC for use with 2SA-10 2-axis angular sensing IC. GMW360A None
2D-VD-11 2-axis Vertical Hall Element. 2D-VH-11 2SA-10G
AN_114KIT 2SA-10 Application Engineering Kit, 360° Angle Sensing, Standard PCB8. AN_114KIT None
AN_134 KIT EM-3242 Non-contact Angle Sensor with "In Range" Detection - Engineering Evaluation Kit AN_134 KIT None
AN_133 KIT EM-3242 Non-contact Angle Sensor without "In Range" Detection - Engineering Evaluation Kit AN_133 KIT None
AN-170KIT CQ-2092 AKM CQ-2092 Application Current Sensing Engineering Kit, ±20A range. AN-170KIT None
AN-116KIT CSA-1V Application Engineering Kit, Current Sensing on a PCB 4-loop track up to 2A RMS7. AN_116KIT None
AN-120KIT CSA-1V Application Engineering Kit, Current Sensing on a PCB top track up to 8A RMS7. AN_120KIT None
AN-118KIT CSA-1V Application Engineering Kit, Current Sensing on a PCB with a jumper up to 8A RMS7. AN_118KIT None
AN-128KIT CSA-1V Application Engineering Kit, Current Sensing on a PCB using dual CSAs to 8A RMS7. AN_128KIT None
AN-122KIT CSA-1V Application Engineering Kit, High Sensitivity Current Sensor 15A RMS7. AN_122KIT None
AN-126KIT CSA-1V Application Engineering Kit, Current Sensing PCB with multi layer traces 20A RMS7. AN_126KIT None
AN-124KIT CSA-1V Application Engineering Kit, Current Sensing High Voltage Isolation Current Sensor 20A RMS7. AN_124KIT None
AN-123KIT CSA-1V Application Engineering Kit, Current Sensing on a PCB with a bus bar up to 25A RMS7. AN_123KIT None
AN-119KIT CSA-1V Application Engineering Kit, Current Sensing in an external wire - no current limit7. AN_119KIT None
AN-119BKIT CSA-1V Application Engineering Kit, Clamp On Current Sensor - no current limit7. AN_119BKIT None
AN-121KIT CSA-1V Application Engineering Kit, Current Sensing on an external bus bar7. AN_121KIT None
AN-130KIT EQ-730L Application Engineering Kit, Gapped Core Current Sensor, up to 12A rms. AN-130KIT None
AN-131KIT EQ-731L Application Engineering Kit, Gapped Core Current Sensor, up to 25A rms. AN-131KIT None
AN-135KIT EQ-732L Application Engineering Kit, Gapped Core Current Sensor, up to 40A rms. AN-135KIT None
AN-136KIT EQ-733L Application Engineering Kit, Gapped Core Current Sensor, up to 80A rms. AN-136KIT None
AN_117KIT Engineering Kit for CSA-1V-SO, to 100A. CSA-1V Application Engineering Kit, Current Sensing on a multi-layer PCB up to 40A RMS7. AN_117KIT None
AN_106-DC KIT and AN_106-AC KIT CSA-1VG-S0 Reference Kit for measuring 0-20A continuous. AN_106-DC KIT and AN_106-AC KIT None
AN-180KIT Reference Design Kit - Thin, High Field Magnetic Sensor, ±1T, 2.5V +/- 1.5V Output AN-180KIT Senis I1A 1-axis
HG-0112, HG-0113 , HG-0114, HG-0115, HG-106R GaAs Hall Element, High linearity, Small, Thin, Motor & Linear position, SMT, 5000pc/reel HG-0112 HG-0113 HG-0114 HG-0115 HG-106R HG-0712
HG-0713
HG-0714
HG-0715
HG106C

Fluxgate Teslameters/Gaussmeters

High sensitivity and accuracy for low magnetic fields. Magnetic fields from appliances and equipment, site surveys and monitoring. Active magnetic field cancellation. Mag-01 Mag-01H
Low Noise Magnetic Field Sensors Mag648-L / Mag649-L None
Low Noise Magnetic Field Sensors Mag648FLL / Mag649FLL None
Low Noise Magnetic Field Sensors Mag648U-L / Mag649U-L None
Submersible Low Noise Magnetic Field Sensors Mag648S-L / Mag649S-L None

Magnetic Field Measurement

Fluxgate Magnometers
Bartington Low Noise Fluxgate Magnetometers (not all models are discontinued) Mag-03MS Mag-13MS
  Mag-03MSES None
  Mag-03MCES Mag-13MC
  Mag-03MSS Mag-13MSS
Linear Hall Transducers
'Probe type Sensor' linear magnetic field measurement, feedback control, field mapping, and quality control. Sentron 3RTP100-2-2 3-axis Senis F3A 3-axis
Sentron was acquired by Senis -- Sentron 3RTP100 and the 3R100 are no longer in production. Sentron 3R100-2-2 3-axis Senis F3A 3-axis
CH3A has been updated and renamed to F3A. Senis CH3A 3-axis Senis F3A 3-axis
YM12 1-axis is no longer in production. I1A is the recommended replacement. Senis YM12 1-axis Senis I1A 1-axis
0Yx has been updated and renamed to F1A. Senis 0Yx 1-axis Senis F1A 1-axis
CO50 Signal Output Cable for older Sentron/Senis Magnetic Field Transducers. The CO50-G is for new Senis Transducers. CO50 CO50-G
Very High Precision NMR Teslameters/Gaussmeters
Calibration of magnetic standards. Very high resolution and stability measurement of magnetic fields. Measures total magnetic field at a single point. FW 101 Total field None
Hand-held Hall Teslameters/Gaussmeters
THM7025 Hand-held, low-cost, 3-axis magnetic field measurement for magnet and fringing fields THM 7025 3-axis THM 1176 3-axis
Digital Voltage Integrators / Fluxmeters
PDI-5025 Precision Digital Integrator for precision magnetic field mapping in space or time by measurement of flux change induced voltages in moving coils or wires. PDI-5025 FDI-2056
Precision Digital Hall Teslameters/Gaussmeter
DTM-130-G Precision measurement and control of magnetic fields for laboratory and process control DTM-130-G 1-axis DTM-133 1-axis
DTM-141-G Precision measurement and control of magnetic fields for laboratory and process control DTM-141-G 1-axis DTM-151 1-axis

Electric Current Measurement

DC Current Transducers For High Current - Multi-channel Systems
Current Transducer DC/AC. IT 150-S and IT 600-S are no longer in production. IT 150-S, IT 600-S Danisense
DS Series
Current Transducer DC/AC. Eurocard Electronic Module and separate Transducer Head. 864I, 864U Danisense
DS Series
Current Measurement System DC/AC. Current or Voltage output. Consisting of a rack mounted Control and a separate current transducer Head. Power supply development, production testing, or power measurement as a secondary current standard. Range programming for Model 860. The 860R-600, 860R-2000, & 860R-5000 are no longer in production. The ITP Series has been renamed and expanded as ITZ Series. 860R-600 860R-2000 860R-5000 (multi-channel) Danisense
DS Series (up to ±3000A)
The 864R is a 19" rack Control that provides power and mounting of up to six Modules. It is ideal for multi-channel or multi-phase power efficiency measurement for currents up to 5,000 amps dc. 864R is no longer in production. 864R (multi-channel) Danisense
DS Series (up to ±3000A, 4-channel)
The Danfysik 866R Multi-channel Current Transducer System utilizes the Ultrastab 866 current transducers to provide a precision multi-channel system with current and voltage outputs for power analysis and quality control applications.

The 866R has been replaced by the DaniSense DSSIU-4 which is a similar 4 channel unit but no longer includes the Voltage Output Monitor. It allows connection of any four DaniSense or LEM IT Transducers with up to 3000A full-scale primary current.
866R Danisense
DS Series (up to ±3000A, 4-channel)
AC Current Transformers for Broad Frequency Response
Current Transformer, AC/Pulse. Bergoz Current Transformer CT Product Line has been purchased by MagneLab, who now manufactures and supports the CT line. GMW continues to provide North American sales and support. Bergoz CT MagneLab CT
Tuned Current Transformers. Bergoz In-Flange TCT TCT None
Electromagnets and Electromagnet Accessories
Kepco BOP Bipolar Power Supplies are no longer available with the -M (manual) option, replaced by the -D (digital LCD) option on all models. BOP20-5M BOP20-10M BOP20-20m BOP20-20ML BOP36-6M BOP36-12M BOP50-2M BOP50-4M BOP50-5M BOP50-8M BOP50-8ML BOP72-3M BOP72-6M BOP100-1M BOP100-2M BOP100-4M BOP200-1M BOP20-5D
BOP20-10D
BOP20-20D
BOP20-20DL
BOP36-6D
BOP36-12D
BOP50-2D
BOP50-4D
BOP50-5D
BOP50-8D
BOP50-8DL
BOP72-3D
BOP72-6D
BOP100-1D
BOP100-2D
BOP100-4D
BOP200-1D

Particle Beam Diagnostics

Charge Monitors Product Replacement Product
The Beam Charge Monitor measures pulsed beams charge from an ICT. It's bipolar output voltage is directly proportional to the total beam charge.

The BCM-CA (Continuous Averaging) version for pulse repetition rates from 10MHz down to 5kHz has been disconinued and replaced with BCM-RF with superior performance: Measures CW and macropulse current with <1uArms total noise over >5 MHz bandwidth. Bunch repetition range: from single to 325 MHz.
BCM-CA BCM-RF
Position Monitors Product Replacement Product
The VWM is based on the wire resonant frequency dependence on its tension, itself dependent on its temperature. No longer in production. VWM None
The Beam Pickup, Four Button is designed for use with the LR-BPM. It has a 47.6mm I.D., with a very short axial length of 76.2mm. Rotateable conflate flanges enable easy assembly with either orthogonal or rotated button orientation. No longer in production. BPM-UHV-50 None

Fiber Optic Links

Analog Signals via Optical Cable Product Replacement Product
PPM p2p Analog Fiber Optic Links allow high fidelity transmission of analog signals that require immunity to electrical interference, high voltage isolation, or long haul signal transmission.

Discontinued Modules:
DC Modules DC - 2MHz, Single Mode Fiber
DC Modules DC - 2MHz, Multi Mode Fiber
DC Modules DC - 2.5MHz, Multi Mode Fiber
DC Modules DC - 10MHz, Single Mode Fiber
PDT-H1-6R, PDT-H1-6H, PDR-H1-6R, PDR-H1-6H, PDT-H1-1R, PDT-H1-1H, PDR-H1-1R, PDR-H1-1H, PDT-R1-1R, PDT-R1-1H, PDR-R1-1R, PDR-R1-1H, PDT-N1-1R, PDT-N1-1H, PDR-N1-1R, PDR-N1-1H Current P2P Modules